fyi guys NVIDIA SLI is broken in 416.81 but works ok in 416.34 dont upgrade if you have SLI I have two GTX 980 Ti's went back to 416.34 and im good now.
Currently, while I've found sli does sorta work, and scale quite well with the latest driver, there's a few bugs involving missing GPU accelerated particles, made a little YouTube vid showing the differences...
You can see the missing effects at several points throughout the clip, inc missing rain/sparks and dynamic leaves.
Currently, while I've found sli does sorta work, and scale quite well with the latest driver, there's a few bugs involving missing GPU accelerated particles, made a little YouTube vid showing the differences...
You can see the missing effects at several points throughout the clip, inc missing rain/sparks and dynamic leaves.
is this using the nvispector hack or the older driver?
Currently, while I've found sli does sorta work, and scale quite well with the latest driver, there's a few bugs involving missing GPU accelerated particles, made a little YouTube vid showing the differences...
You can see the missing effects at several points throughout the clip, inc missing rain/sparks and dynamic leaves.
is this using the nvispector hack or the older driver?
Current driver, but SLI compatibility bits set to bf1/sw battlefront etc.. I see the same results with the previous driver too though.
Hello,so can i install the driver 416.34 back and it still not working the Sli.
After that i did tray to put the settings from BF1 on the BFv profile with nvidia insepctor and still not working. DO you know how to make this work with the 416.34 driver ? thanks.
Hello,so can i install the driver 416.34 back and it still not working the Sli.
After that i did tray to put the settings from BF1 on the BFv profile with nvidia insepctor and still not working. DO you know how to make this work with the 416.34 driver ? thanks.
It should work fine with the 416.34 driver, no tweaking needed, just make sure you're in dx11 mode as dx12 doesn't work with multi gpu in bfV yet. You don't need to change anything in the control panel either, just leave everything on "Nvidia recommended" settings and it'll automatically use both cards.
You only need to use nvinspector if you're using 416.81, then I'd either recommend the bf1 compatibility bits or the star wars battlefront II bits, both work equally well, but you'll be missing some effects like rain/sparks/snow and dynamic leaves. (*note, those effects will also be missing using the older driver) Using the newer driver, you'll notice that under ""Sli rendering mode" in the control panel, it'll still say "single gpu", don't change it, as long as you've changed the compatibility bits it'll still run using both cards, if you try to force AFR the game will hang on the intro screen.
Comments
(also ray tracing would be nice too)
But yeah, i REALLY hope they give official sli support...
It did, I played with it briefly yesterday without issue, installed the newest drivers and now my second card sits idle
They work in conjunction with Dice according to this post on the Nvidia forums: https://forums.geforce.com/default/topic/1079181/geforce-drivers/official-416-81-game-ready-whql-display-driver-feedback-thread-released-11-8-18-/post/5910161/#5910161
You can see the missing effects at several points throughout the clip, inc missing rain/sparks and dynamic leaves.
It’s frustrating to see this is still going on, even after news outlets picked up on the issue and called out NVIDIA.
Time to sell my two Titan Xp and switch to a single 2080Ti
Current driver, but SLI compatibility bits set to bf1/sw battlefront etc.. I see the same results with the previous driver too though.
I have 2 2080ti's and they are horrible when it comes to performance on BF1 and BFV by now...
Same, I'm selling one. 2 x RTX 2080Ti are a nightmare with NVLINK and the SLI profile, complete mess.
After that i did tray to put the settings from BF1 on the BFv profile with nvidia insepctor and still not working. DO you know how to make this work with the 416.34 driver ? thanks.
It should work fine with the 416.34 driver, no tweaking needed, just make sure you're in dx11 mode as dx12 doesn't work with multi gpu in bfV yet. You don't need to change anything in the control panel either, just leave everything on "Nvidia recommended" settings and it'll automatically use both cards.
You only need to use nvinspector if you're using 416.81, then I'd either recommend the bf1 compatibility bits or the star wars battlefront II bits, both work equally well, but you'll be missing some effects like rain/sparks/snow and dynamic leaves. (*note, those effects will also be missing using the older driver) Using the newer driver, you'll notice that under ""Sli rendering mode" in the control panel, it'll still say "single gpu", don't change it, as long as you've changed the compatibility bits it'll still run using both cards, if you try to force AFR the game will hang on the intro screen.
Cards only at 40% usage and cant get over 60FPS
2x1080ti with 5960x @4.4Ghz
Please help if anybody can advise